This is an old revision of the document!
Bandsaw, Horizontal - Hafco BS-7DS
Aliases | - |
Other References | |
Official Maintainer | Phil Juric |
Current Status
Working
Note: If the machine has issues starting, isolate immediately and contact Phil Juric
Usage
This machine requires induction to use.
Book an induction in Eventbrite.
https://www.eventbrite.com/d/australia--south-brisbane/hsbne-inc-bandsaw/?page=1
Personal Protective Equipment
Required | Always wear AS/NZS 1337.1 compliant safety glasses while operating this machine. | |
Required | Enclosed shoes are required, no open sandals, thongs etc | |
Required | Restrain hair while operating machine | |
Prohibited | Loose clothing and jewellery not to be worn while operating this machine. |
Recommended | We recommend hearing protection. | |
Warning | Entanglement hazard present while wearing gloves. | |
Maintenance | Disconnect power to the machine before performing maintenance, including wheel changes |
Machine Specifications
Name | Value |
---|---|
Motor Power | 750W 240V |
Blade Size | 2362x19x0.8 |
Rectangular Capacity @ 90° | 215mm X 178mm |
Rectangular Capacity @ 45° | 140mm x 85mm |
Blade Speeds | 24, 41, 61, 82mpm |
Mitre Angle Limits | -45°, +45° |
Weight | 165kg |
Documents
Supplier
- Hare & Forbes MachineryHouse
- P 07 3715 2200
Known Issues
Date | Description | Workaround | Proposed Remediation |
---|
Modifications / Repair History
Date | Modified By | Description | Remediation | Cost |
---|---|---|---|---|
17/11/2020 | Eris Ryan | Fletcher Barnes had breaker tripping | Tested fine. 10M Ohm to earth. Put back into service. | $0 |
08/12/2020 | Eris Ryan | Blade not moving | Blade had come loose, reattached and tightened | $0 |
08/12/2020 | Ryan Marple | All bandsaw blades dull | Purchased 2 new bi-metal blades | $110 |
08/12/2020 | Ryan Marple | Fasteners holding cover require different tools to open | Replaced fasteners with wing screws | $20 |
04/01/2022 | Dave Seff | Repaired water damaged interlock | Replaced contactor | $70 |
Accessories
Image | Category | Accessory Name & Notes | Location | Buy from |
---|---|---|---|---|
Consumables & Running Costs
Image | Category | Accessory Name & Notes | Location | Buy from |
---|---|---|---|---|
Coolant | Penrite Soluble Oil Mixed with water to create cutting fluid. | Stored in metal shop chemical cabinet | Penrite Soluble Oil 20L Drum | |
Blade | 2362 x 19 x 0.80mm Bandsaw Blade Bi-metal blades are preferred due to their longer lifespan than regular blades. The preferred blade is bi-metal 6-10TPI. | Hung above metal shop chemical cabinet | 6-10TPI Bi-Metal Blade (Preferred) 4-6TPI Bi-Metal Blade 10-14TPI Bi-Metal Blade 6TPI Carbon Steel 8TPI Carbon Steel 10TPI Carbon Steel 14TPI Carbon Steel |
Maintenance
Interval | Task |
---|---|
Daily | Top up coolant tank with tap water |
Weekly | Oil vice lead screw and machined surfaces |
RACI
Task / Action | Executive | Cause Leader Cause Team | Named Maintainer | Trainers | Cause | Membership | Implementer |
---|---|---|---|---|---|---|---|
Modification and Repairs | - | AC | C | I | I | I | R |
Induction changes | C | RACI | RC | I | I | I | R |
Daily Maintenance | - | - | I | - | - | - | R |
Weekly Maintenance | - | - | RAI | - | - | - | R |
Changing Blade | - | - | - | - | - | - | R |
Setting cut angle | - | - | - | - | - | - | R |
Risk Matrix and Mitigation
Ref / ID | Pre-Mitigation | Mitigations / Warnings / Remedies | Post Mitigation | ||||||
---|---|---|---|---|---|---|---|---|---|
Risk | Risk Severity | Risk Likelyhood | Risk Level | Risk Severity | Risk Likelyhood | Risk Level | Acceptable to Proceed | ||
0001 | Projectile | Intolerable | Probable | 12 | Induction required. Require use of appropriate PPE. | Low | Possible | 2 | Yes |
0002 | Entanglement | Intolerable | Probable | 12 | Induction required. Discourage glove use during operation. Prohibit long hair & jewellery. | Low | Possible | 2 | Yes |
0003 | Laceration/Dismemberment | Intolerable | Possible | 11 | Induction required. Require use of appropriate PPE. | Low | Improbable | 1 | Yes |
0004 | Heat burn from workpiece | Undesirable | Possible | 8 | Induction required. Always ensure coolant is working properly. Feel workpiece temperature before grabbing it. | Low | Improbable | 1 | Yes |
Decision Register
Ref / ID | Decision Details | Impact | Proposed Date | Proposed By | Status | Approved By | Date | Resulting Actions and Comments |
---|
- tools/metalshop/bandsaw.1651568691
- Last modified: 2 years ago
- by philip.juric