Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
howto:upmini [2020/10/17 13:31] hsbnewiki |
howto:upmini [2020/10/17 13:45] hsbnewiki |
||
---|---|---|---|
Line 5: | Line 5: | ||
- Take a look at the printer filament spool and ensure there's enough filament on the roll for your print. | - Take a look at the printer filament spool and ensure there's enough filament on the roll for your print. | ||
- A good rule of thumb is for every square CM of your print there should be 15CM on the spool. | - A good rule of thumb is for every square CM of your print there should be 15CM on the spool. | ||
+ | - If there is not enough filament on the spool change it following the instructions below. | ||
- Initialise Printer | - Initialise Printer | ||
- On the attached PC, run the 'UP 2.18' software. <callout type="info" icon="true">Make sure you have opened Up 2.18, the 'Up Studio' software currently does not work with this printer.</callout> | - On the attached PC, run the 'UP 2.18' software. <callout type="info" icon="true">Make sure you have opened Up 2.18, the 'Up Studio' software currently does not work with this printer.</callout> | ||
Line 16: | Line 17: | ||
- The printhead will start to heat up, within 5 minutes the printhead temperature will reach 260 degrees then the printer will buzz and the print head starts to extrude. | - The printhead will start to heat up, within 5 minutes the printhead temperature will reach 260 degrees then the printer will buzz and the print head starts to extrude. | ||
- Watch the printer push the filament out, making sure it's not coming out sideways. If it is, report it to the #digifab chat. | - Watch the printer push the filament out, making sure it's not coming out sideways. If it is, report it to the #digifab chat. | ||
- | - When it completes it will beep again, pull the filament out and it should be a nice smooth coil of filament. <alert type="danger" icon="fa fa-warning">Do not reach up towards the nozzle, reach down towards the bed.</alert><callout type="info" icon="true">If the filament is bubbly or textured or doesn't come out at all, report this to #digifab chat..</callout></WRAP> | + | - When it completes it will beep again, pull the filament out and it should be a nice smooth coil of filament. <alert type="danger" icon="fa fa-warning">Do not reach up towards the nozzle, reach down towards the bed.</alert><callout type="info" icon="true">If the filament is bubbly or textured or doesn't come out at all, report this to #digifab chat.</callout> |
- Set up Print | - Set up Print | ||
- Clean off Bed | - Clean off Bed | ||
- | Changing Filament | + | ====== Changing Filament ====== |
+ | |||
+ | ===== Unloading filament spools ===== | ||
+ | - Initialize the printer by going to 3d Print → Initialise | ||
+ | - Go to 3D Print → Maintenance from the top menu bar. | ||
+ | - Click Withdraw to remove the current filament spool. | ||
+ | - The printer will heat its nozzle to the appropriate temperature and will beep when it is ready. | ||
+ | - Gently pull the filament out of the extruder. The filament should remove smoothly from the extruder. | ||
+ | - If you feel a tug from the extruder, stop pulling and repeat step 2 onwards. | ||
+ | |||
+ | ===== Loading filament spools ===== | ||
+ | - Initialize the printer by going to 3d Print → Initialise | ||
+ | - Go to 3D Print → Maintenance from the top menu bar. | ||
+ | - Click New Spool. | ||
+ | - Select the type of filament (ABS) and enter the approximate amount in grams. Brand new UP! Mini spools are 700g. | ||
+ | - If you are unsure of the amount, leave the default number and click OK. | ||
+ | - Trim the end of the filament with the orange clippers. | ||
+ | - Feed the new filament through the guide on the back of the printer and into the guide tube. | ||
+ | - Have the filament end ready by the extruder. | ||
+ | - Click Extrude. The nozzle will again heat up to the appropriate temperature and will beep when it is ready. | ||
+ | - Place the new filament in the slot on top of the extruder and gently push. The extruder should grab the filament easily and start extruding from the nozzle. | ||
+ | - Release the filament. | ||
+ | - The printer will beep when the extrude cycle is complete. | ||
+ | - If changing colors, run the Extrude cycle twice to remove old filament. |
- howto/upmini
- Last modified: 4 years ago
- by hsbnewiki