Differences

This shows you the differences between two versions of the page.

--- tools:woodshop:tablesaws [2021/02/14 00:58]
ale [Crosscut Fence Stops]
+++ tools:woodshop:tablesaws [2022/02/26 15:40]
ale [Modifications / Repair History]
@@ Line 1: / Line 1: @@
+~~TOC 1-4~~
 <WRAP column third>
 {{:tools:woodshop:ps-12-sliding-table-panel-saw.jpg?400&nolink}}
@@ Line 4: / Line 5: @@
 <WRAP column twothirds>
 ====== Ledacraft PS-12 305mm Sliding Panel Table Saw ======
-| Aliases | "the table saw", "PS12"  |
+| Aliases              | "the table saw", "PS12"                                                                                                                                                                                               |
-| Other References |<WRAP>
+| Other References     | <WRAP>  //[[https://snipe.hsbne.org/|Asset Register]]//    //[[https://xero.com/|Xero Asset]]//    //[[https://portal.hsbne.org/|Portal]]//    [[https://forum.hsbne.org/search?q=table%20saw|Forum Posts]]  </WRAP>  |
-//[[https://snipe.hsbne.org/|Asset Register]]//
+| Official Maintainer  | Ale Moré                                                                                                                                                                                                              |
-//[[https://xero.com/|Xero Asset]]//
-//[[https://portal.hsbne.org/|Portal]]//
-[[https://forum.hsbne.org/search?q=table%20saw|Forum Posts]]
-</WRAP>|
-| Official Maintainer | Joshua Hogendorn |
 </WRAP>
 <WRAP clear></WRAP>
@@ Line 22: / Line 14: @@
 <WRAP warning 50% round>
-=== Usable ===
+==== Usable ====
 The scribing blade mechanism has been removed for servicing.
@@ Line 31: / Line 23: @@
 ===== Usage =====
+====Induction===
 <WRAP round info 50%>
 **This machine <wrap hi>requires induction</wrap>.**
@@ Line 46: / Line 39: @@
     * Joshua Hogendorn
     * Ale More
+====Guidelines====
+=== How to use the microadjustment ===
+**Note:** To have a better understanding of this technique, you might want to check [[tools:woodshop:tablesaws#crosscut_fence_stops1|the modifications that we made to the endstops]].
+  - With the swivel hard against the stop, set the stop to a dimension that's smaller than the nominal dimension by an amount that you think is suitable (E.g. how much macro-adjustment you need).
+  - Back the swivel paying attention to the gauge on the micro-adjustment knob and go pass the nominal dimension.
+  - Take a cut, measure using the method of your preference and adjust accordingly.
 ==== Recommended PPE ====
@@ Line 85: / Line 88: @@
 ===== Manufacturer =====
-=== Ledacraft ===
+==== Ledacraft ====
   * E sales@ledamachinery.com.au
@@ Line 91: / Line 94: @@
   * [[https://www.ledamachinery.com.au/leda_product/ps-12-1600mm-sliding-table-panel-saw/]]
-=== Reseller ===
+==== Reseller ====
   * Lance Dargusch
@@ Line 98: / Line 101: @@
   * M 0408 765 922
-=== Known Identical Models ===
+==== Known Identical Models ====
   * [[https://www.carbatec.com.au/machinery-and-accessories/tablesaws-and-accessories/tablesaws/ts-p1600p]]
@@ Line 131: / Line 134: @@
 | - | Joshua H & Ian Redmond | Rise and fall gear/worm totally worn and failed. | Replacement parts ordered but incorrect due to machine revision. Fix found by rotating gear 180º to unworn section | ~$150  |
 | - | Ryan Marple & Ale Moré | Rise and fall gear/worm totally worn and failed. | Parts were milled, specifically, holes were slotted to allow the installation of a different size worm wheel. | -|
+| 14/02/2021 | Ryan Marple & Ale Moré | The stops couldn't be calibrated with ease | Crosscut endstops were modified with an adjustable bullseye | -|
 ==== Crosscut Fence Stops ====
@@ Line 137: / Line 142: @@
 {{:tools:woodshop:table_saw_stop_1.jpg?400|}} {{:tools:woodshop:table_saw_stop_2.jpg?400|}}
-=== How to use the microadjustment ===
-  - With the swivel hard against the stop, set the stop to a dimension that's smaller than the nominal dimension by an amount that you think is suitable (E.g. how much macro-adjustment you need).
-  - Back the swivel paying attention to the gauge on the micro-adjustment knob and go pass the nominal dimension.
-  - Take a cut, measure using the method of your preference and adjust accordingly.
 ===== Accessories =====
@@ Line 176: / Line 174: @@
 | Quarterly | Assess and send blades for sharpening |
 | Monthly | Assess sliding table height and angle relative to main table and blade. Nominal 0.05-0.1mm proud of main table, parallel to blade. |
+====Sharpening log====
+^ Date        ^ Blade            ^ Notes                             ^
+| 13/09/2021  | TCG Acrylic      | Sharpen by Brisbane Saw Services  |
+| 13/09/2021  | TCG (Laminates)  | Sharpen by Brisbane Saw Services  |
 ===== RACI =====