{{:tools:digitalfabrication:3dprinters:crx.jpg?nolink&400|}} ====== Creality CR-X (Right) ====== | Aliases | "Left Right CR-X" | | Octoprint Link | [[http://rightcrx.digifab/]] Username and password are both "hsbne" | | Other References | //[[https://snipe.hsbne.org/|Asset Register]]// //[[https://portal.hsbne.org/|Portal]]// [[https://forum.hsbne.org/search?q=left%20crx|Forum Posts]] | | Official Maintainer | Digifab Tab | ===== Current Status ===== === Working === This machine is working as expected. NOTE: This printer was previously the left CR-X, and has been moved into the position of the right CR-X; The old right CR-X has been decommissioned. ==== Octoprint ==== This tool uses Octoprint at [[http://rightcrx.digifab/]]. Username and password are both "hsbne". ===== Usage ===== The induction for this machine consists of reading each of the following (in full!): * [[tools:digitalfabrication:3dprinters:|3D printers wiki page]], which links to... * The [[howto:octoprint|Starting a Print with Octoprint]] guide. * The page you are currently on Once you have fully read and understood each of the pages above, you can use this machine. The link to this particular machine's Raspberry Pi hosted Octo Print is [[http://rightcrx.digifab/]]. ===== Machine Specifications ===== === Maximum Print Area === ^ Name ^ Value ^ | Length | 300mm (250 recommended) | | Width | 300mm (250 recommended) | | Height | 400mm (300 recommended) | === Maximum Print Temperatures === ^ Name ^ Value ^ | Extruder | 240 Degrees Celcius (Above this will damage the hotend and cause the teflon to release toxic fumes) | | Print Bed | 100 Degrees Celcius (the print bed will not work well at temperatures in excess of this) | === Manufacturer === * [[https://www.creality3dofficial.com/]] === Reseller === * Jaycar * P 1800 022 888 * [[https://www.jaycar.com.au/creality-dual-filament-3d-printer-cr-x/p/TL4410]] ===== Known Issues ===== * None currently ===== Modifications / Repair History ===== ^ Date ^ Modified By ^ Description ^ Remediation ^ Cost ^ | 01/01/2020 | PLACEHOLDER NAME | PLACEHOLDER Describe what happened | PLACEHOLDER Describe how it was fixed or modified | PLACEHOLDER document the cost of the change | ===== Consumables & Running Costs ===== ^ Image ^ Category ^ Accessory Name & Notes ^ Location ^ Buy from ^ | PLACEHOLDER Image, 100 width | Filament | **PETG and PLA Filament 1.75mm** | This consumable is stored on each printer with spares under the bench near the main door. | https://www.bilby3d.com.au/DispProd.asp?CatID=&SubCatID=108&ProdID=PLA3Black1E | ===== Maintenance ===== ^ Interval ^ Task ^ | Before **every** use | Check print bed is free from dust and other debris, and ensure the entire bench is 100% free from debris and tools. | | As needed | Tighten the stepper belts. | | As needed | Calibrate bed level / height. | | PLACEHOLDER Pick one: Daily/Weekly/Monthly/Quarterly/Biannual/Annual | PLACEHOLDER Description of maintenance task and any relevant parameters | ===== Risk Matrix and Mitigation ===== {{:tools:woodshop:riskmatrix3x3.png?direct|}} ^ Ref / ID ^ Pre-Mitigation |||^ Mitigations / Warnings / Remedies ^ Post Mitigation |||^ ^ ::: ^ Risk ^ Risk Severity ^ Risk Likelyhood ^ Risk Level ^ ::: ^ Risk Severity ^ Risk Likelyhood ^ Risk Level ^ Acceptable to Proceed ^ | 0001 | Burns | Undesirable | Possible | 8 | Induction to train users in correct usage and use appropriate tools when touching any hot part of the machine. | Acceptable | Improbable | 1 | yes | | 0002 | Cuts / lacerations to skin | Undesirable | Possible | 8 | Require users to wear gloves when cleaning up prints with any sharp tool. | Acceptable | Improbable | 1 | yes | ===== Decision Register ===== ^ Ref / ID ^ Decision Details ^ Impact ^ Proposed Date ^ Proposed By ^ Status ^ Approved By ^ Date ^ Resulting Actions and Comments ^ | 0001 | Finish wiki and put machine into service | Members can use the machine. | 30/12/20 | Jaimyn Mayer | Approved | Jaimyn Mayer | 30/12/20 | - |